www.austriamicrosystems.com/AS5140H
Revision 1.4
16 - 37
AS5140H
Data Sheet - Detailed Description
Incremental Power-up Lock Option. After power-up, the incremental outputs can optionally be locked or unlocked, depending on the
status of the CSn pin:
CSn = low at power-up: CSn has an internal pull-up resistor and must be externally pulled low (
). If Csn is low at power-up,
the incremental outputs (A, B, Index) will be high until the internal offset compensation is finished. This unique state (A=B=Index = high)
may be used as an indicator for the external controller to shorten the waiting time at power-up. Instead of waiting for the specified maximum
power up-time (0), the controller can start requesting data from the AS5140H as soon as the state (A=B=Index = high) is cleared.
CSn = high or open at power-up: In this mode, the incremental outputs (A, B, Index) will remain at logic high state, until CSn goes low or a
low pulse is applied at CSn. This mode allows intentional disabling of the incremental outputs until, for example the system microcontroller
is ready to receive data.
7.2.3 Incremental Output Hysteresis
To avoid flickering incremental outputs at a stationary magnet position, a hysteresis is introduced. In case of a rotational direction change, the
incremental outputs have a hysteresis of 2 LSB. Regardless of the programmed incremental resolution, the hysteresis of 2 LSB always
corresponds to the highest resolution of 10 bit. In absolute terms, the hysteresis is set to 0.704 degrees for all resolutions. For constant rotational
directions, every magnet position change is indicated at the incremental outputs (see Figure 9). For example, if the magnet turns clockwise from
position x+3 to x+4 , the incremental output would also indicate this position accordingly. A change of the magnets rotational direction back to
position x+3 means that the incremental output still remains unchanged for the duration of 2 LSB, until position x+2 is reached. Following this
direction, the incremental outputs will again be updated with every change of the magnet position.
Figure 9. Hysteresis Window for Incremental Outputs
7.3 Pulse Width Modulation (PWM) Output
The AS5140H provides a pulse width modulated output (PWM), whose duty cycle is proportional to the measured angle:
Position =
(EQ 2)
The PWM frequency is internally trimmed to an accuracy of ?% (?0% over full temperature range). This tolerance can be cancelled by
measuring the complete duty cycle as shown above.
R
ext
5k?/DIV>
d
Clockwise Direction
Counterclockwise Direction
X+1 X+2 X+3 X+4 X+5
X
Magnet Position
X
X+1
X+2
X+3
X+4
Hysteresis:
0.7?/DIV>
Incremental
Output
Indication
t
on
1025
?/DIV>
t
on
t
off
+
(
)
---------------- -------- -
1
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AS5145B-HSST-500
IC ENCODER ROTARY MAGN 16-SSOP
AS5510-DWLT
IC ENCODER MAGNETIC LIN 6-WLCSP
ATS137-PL-B-B
IC HALL SENSOR SGL 25MA SIP-3L
ATS177-PG-B-B
IC HALL SENSOR LATCH 25MA SIP-3L
ATS617LSGTN-T
IC HALL EFFECT GEAR SENSOR 4SIP
ATS625LSGTN-T
IC SENSOR GEAR TOOTH 4-SIP
ATS627LSGTN-T
IC HALL EFFECT GEAR SENSOR 4-SIP
ATS635LSETN-T
IC SENSOR GEAR TOOTH 4-SIP
相关代理商/技术参数
AS5140H-ASST-500
功能描述:板机接口霍耳效应/磁性传感器 RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
AS5140HASSU
制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:10-Bit 360 Programmable Magnetic Rotary Encoder For High Ambient Temperatures
AS5140H-ASSU
功能描述:IC ENCODER PROG 10-BIT 16-SSOP RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
AS5140H-DB
制造商:ams 功能描述:AS5140H Demo Board
AS5140H-PB
制造商:ams 功能描述:AS5140H Progamming Board
AS5140-SS_EK_AB
功能描述:AS5140 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:5V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5140 标准包装:1
AS5140-SS_EK_DB
功能描述:AS5140 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板，线缆 使用的 IC/零件:AS5140 标准包装:1
AS51430FLF
制造商:TT Electronics / IRC 功能描述:AS51430FLF